Brands Guides About
Sony EBRIDGE1CR IP over Coax Ethernet Receiver — main product image
Sony

Sony EBRIDGE1CR IP over Coax Ethernet Receiver

Extend IP network connectivity up to 1,500 feet over existing RG59/RG6 coax — no new cable pulls required for IP camera migration.

$150.71*
✓ In Stock on Amazon.com
View on Amazon

*Price sourced from Amazon.com. Last updated:Jul 14, 2026.Price and availability are subject to change.

Affiliate Disclosure: Studio Supplies may earn a commission from qualifying purchases made through links on this page, at no additional cost to you. This helps support our editorial team.

Notice a mistake? Let Us Know

Overview

The Altronix EBRIDGE1CR is the receiver component of a coaxial-to-Ethernet IP extension system, designed to solve a specific infrastructure problem: delivering IP network connectivity to locations that have existing coaxial cable but lack Cat5e/Cat6 Ethernet runs. The unit accepts the Ethernet-over-coax signal from a compatible Altronix eBridge transmitter, converts it back to 10/100Base-TX Ethernet, and presents a standard RJ-45 port to connected IP devices. The 1,500-foot operating range over RG59 or RG6 coax is the headline specification — it extends the effective reach of an IP network segment to nearly five times the distance standard Ethernet supports, which is the critical capability in large facilities like warehouses, parking structures, and multi-building campuses where the coax backbone from legacy analog CCTV systems is already in place.

The primary deployment scenario for the EBRIDGE1CR is analog-to-IP security system migration. Buildings with extensive analog CCTV coax runs can be upgraded to IP cameras and access control without the labor cost of pulling new structured cabling to every camera position — the eBridge system reuses the existing coax as the transmission medium. At 100Mbps throughput, bandwidth is adequate for single-channel IP camera streams at standard and high-definition resolutions. This unit is designed for security integrators and facilities managers who understand the trade-off: leveraging existing infrastructure at the cost of limiting throughput to Fast Ethernet speeds. For organizations with high-density IP camera deployments at each coax endpoint or plans for high-bitrate multi-stream recording, gigabit-capable alternatives should be evaluated.

Key Features

Altronix EBRIDGE1CR

Specifications

Model
EBRIDGE1CR
Function
IP over Coax Ethernet Receiver

Pros & Cons

👍 Pros

  • 1,500-foot transmission range over existing coax dramatically exceeds the 328-foot limit of native Ethernet, enabling IP connectivity in locations where new cable pulls are impractical.
  • Leverages installed coax infrastructure — in buildings already wired for analog CCTV, no new cabling investment is required to migrate to IP-based systems.
  • 10/100Base-TX Ethernet output is sufficient bandwidth for the IP cameras, access control readers, and intercoms that are the primary use case for this type of media converter.
  • RJ-45 output connects to standard IP equipment without adapters — the transition from coax to Ethernet is transparent to connected devices.
  • Single-port focused design simplifies point-to-point IP extension without the configuration overhead of managed switches or network hardware.

👎 Cons

  • 10/100Base-TX tops out at 100Mbps — this unit cannot support gigabit throughput, which limits it to bandwidth-modest devices and rules it out for high-resolution multi-stream IP camera applications at full bitrate.
  • Requires a compatible Altronix eBridge transmitter at the source end — the EBRIDGE1CR is the receiver half of a two-unit system; the transmitter is not included and must be purchased separately.
  • Power requirements are not fully specified in available product data, creating uncertainty about local power sourcing requirements during installation planning.
  • PoE pass-through capability is unconfirmed — installers planning to power remote IP cameras via PoE cannot verify support without additional research or vendor contact.
  • Single port per unit means multi-device locations require multiple receiver units, increasing per-location cost relative to solutions that support multi-port extension.

Frequently Asked Questions

The EBRIDGE1CR is a coax-to-Ethernet media converter (receiver unit). It receives a 10/100Base-TX Ethernet signal that has been transmitted over coaxial cable from a compatible transmitter (sold separately), converting it back to a standard RJ-45 Ethernet connection at the remote end. It eliminates the need to pull new Cat5/Cat6 cable to locations that already have coax runs.
1,500 feet over standard RG59 or RG6 coaxial cable. This is substantially longer than the 328-foot (100-meter) limit of standard Cat5e/Cat6 Ethernet — a meaningful advantage when wiring large facilities, warehouses, or campuses with existing coax infrastructure.
10/100Base-TX (Fast Ethernet), supporting up to 100Mbps. This is sufficient for IP camera streams, access control systems, and similar bandwidth-modest IP devices, but will not support gigabit throughput for high-bandwidth applications.
The product specifications do not list a power input in the provided data. Altronix eBridge units typically require a local power source at the receiver end — verify the power requirements and included accessories before deployment to avoid on-site installation delays.
The product description does not specify PoE pass-through capability. Users intending to power IP cameras or access points via PoE over this link should verify PoE compatibility with Altronix directly, as PoE pass-through is not confirmed in the available product data.

Related Products